Baseboard Heating Brass Zone Control Valve PN10 2.5 NM Torque

Boiler zone heating valves, brass zone valves for baseboard heating, 2 point control

 

Product Description

 

The motorised ball valve is intended to be used in closed circuits only. Our zone control valve is a range of 2-way motorized zone valve, which is with motor actuator for use in heating and cooling system. The brass or stainless ball valve is available in DN15-32, PN10 with thread connection. The actuator is controlled by 2-point signal and is recommended for on/off function, available for 230V AC, 50/60Hz or DC power supply.

Features

1. Extreme long service life span ;

2. Manual Override, the valve can be operated when power failure;

3. Mini dimension and position indicator

4. Good sealing performance, IP65 enclosure

 

Application

Advantages

• Sturday valve body with reasonable structure design, and best material to be used

No.	Ours	Normal products
Valve shaft seal	Quadruple seals	Dual seals
Nut seal	Auto super anaerobic glue coating, Consistent torque tightening	Manual anaerobic glue, unevenly, non consistent torque tightening
Seal between valve body and housing	Seal groove	none
Torque	Smoothly and light	Heavy, non consistently
Drainage	Yes	none

 

Technical data

Model	25S
Work Current (mA)	<80
Protection	IP65
Power (W)	<2
Operate pressure (Mpa)	PN10
Torque (NM)	2.5
Diameter range (mm)	DN8-DN32 two way DN8-DN20 three way
Open/close time (S)	<8
Work voltage (V)	DC3-6V; DC12V; AC/DC9-24V; AC220V; AC85-265V
Liquid temperature (℃)	0-90
Control mode	CR01; CR02; CR03; CR04; CR05

 

Wiring options

• Two wires and reverse polarity (DC3-6V / DC12V / DC24V)

1. Connecting SW to OPEN , the valve opens , getting the position ,automatically power off, the valve remain fully open position

2. Connection SW to CLOSE , the valve close , getting the position ,automatically power off, the valve remains side passes position(fully closed)

• Three wires and two control points (DC3-6V / DC12V / DC24V)

1. Connecting SW to OPEN, the valve opens , getting the position ,automatically power off, the valve remain fully open position

2. Connection SW to CLOSED, the valve close , getting the position ,automatically power off, the valve remains side passes position (fully closed)

Note: AC24V/AC220V can only be used for 50K series electric valves

• Three wires and one control point (DC3-6V/12V /ADC9-24V /AC220V)

1. Connecting SW, the valve opens , getting the position ,automatically power off, thevalve remain fully open position

2. Disconnecting SW, the valve close , getting the position ,automatically power off, the valve remains side passes position (fully closed)

Note: When power is DC voltage and Red Wires is “+”,Blue wire is “—”

• Two wires and power off return (DC3-6V/ADC9-24V/AC220V)

1. SW connecting, the valve open, getting the position and the power off automatically, the valve remains fully open/close position

2. SW disconnecting, the valve close, getting the position and power off automatically, the valve remains fully open/close position

• Five wires micro conntroller with signal feedback (DC3-6V/12V/24V)

1. Connecting SW and OPEN, the valve opens, getting the position green wire output the OLS signal, the controller tests the signal OLS, connect SW to STOP, the valve stops and remains fully open position

2. Connecting SW and CLOSE, the valve close, getting the position red wire output the CLS signal, the controller tests the signal CLS, connect SW to STOP, the valve stops and remains fully close position,

Note: Please make sure the signal wires "red", "black" and "green" be connected at first, then connect the power wires " yellow" and "blue".

 

Factory show